Fisher & Paykel DD605 Manual do Utilizador

DishDrawerInstallation instructionsNZ AU GB IEDD605 and DS605 models

8DishDrawer® and Standpipe Ø38 mm Water Pressure Max Min Water softener models 1 MPa (145 psi) 0.1 MPa (14.5 psi) Other models 1 MP

9Plumbing and drainage - OPTION 1 (connection)DOUBLE MODELS2750-882.5mm 38 mmmax. 120mm43211180o7If space is limited for fixing, push hose through

10DishDrawer® using sink trap with drain hose joinerPlumbing and drainage - OPTION 2 DOUBLE MODELS750 - 882.5 mmWasteValveWater supply(COLD)Supplied d

11Plumbing and drainage - OPTION 2 (connection)DOUBLE MODELS23750-882.5mm14321180oDishDrawer® using sink trap with drain hose joinerIf space is limite

12Fitting the toekick1234 5 6 78 91019910DOUBLE MODELSImportant!D o not overtighten screw.

13

14Product dimensionsABCEDFGHJKLProduct dimensions (mm)Pre nishedLCD DS605Pre nishedFlat doorDS605 IntegratedDS605Aoverall height* of product409 409

15 Cabinetry dimensionsABCDCabinetry dimensions (mm)Pre nishedLCD DS605Pre nishedFlat doorDS605 IntegratedDS605Ainside height of cavity412 412 412B

16Cavity preparationCavity These marks indicate mounting tab screw locations Note: To align drawer front to adjacent cabinetry, the product to coun

17SINGLE MODELS Route the hoses and move into the cavity111222Tie together to avoid kinking1b21aEnsure hoses and cordare not kinked or twisted.

Safety and warnings Important safety precautions! Installation of this DishDrawer® requires basic mechanical and electrical skills. Be sure to leave

18Removing the tub and securing the product230 mm15534SINGLE MODELS34Ensure the tub is removed and then rotated counter-clockwiseto prevent kinked hos

19 Re tting the tub214543SINGLE MODELS5Before refitting the tub, ensure the hoses are not twisted and the latches at the rear of each drawer runner

20DishDrawer® and Standpipe Ø38 mm Water Pressure Max Min Water softener models 1 MPa (145 psi) 0.1 MPa (14.5 psi) Other models 1 M

21Plumbing and drainage - OPTION 1 (connection)21750-882.5mm 38 mmmax. 120mm4321180oDishDrawer® and Standpipe Ø38 mmSINGLE MODELSIf space is limite

22Plumbing and drainage - OPTION 2 DishDrawer® using sink trap with drain hose joiner750 - 882.5 mmValveWasteWater supply(COLD)Supplied drain hose joi

23Plumbing and drainage - OPTION 2 (connection)23750-882.5mm 38 mmmax. 120mm14321180oDishDrawer® using sink trap with drain hose joinerSINGLE MODEL

24Final checklist Check all parts are installed. Ensure product is level, securely fastened to the cabinetry and opens and closes freely. The DishDraw

Copyright © Fisher & Paykel 2007. All rights reserved.The product specifications in this booklet apply to the specific products and models describ

1ContentsDOUBLE MODELS Product and cabinetry dimensions 2Installation Cavity preparation 4 Route the hoses and move into the cavity 5 Remov

2Product dimensionsOBCEDFGHJNPProduct dimensions (mm)Pre nishedLCD DD605Pre nishedFlat doorDD605 IntegratedDD605Aoverall height* of product819.5 -

3 Cabinetry dimensionsABCDCabinetry dimensions (mm)Pre nishedLCD DD605Pre nishedFlat doorDD605 IntegratedDD605Ainside height of cavity820 - 882.5 8

4Note: Services can be located either side of DishDrawer®.Cavity preparationParts supplied These marks indicate mounting tab screw locations Prefer

5 Route the hoses and move into the cavityDOUBLE MODELS2111233optional1b2optional1aTie together to avoid kinkingIf top two tabs are being used, ensur

6Removing the tub and levelling the product30 mmx 4123455123453DOUBLE MODELS4Ensure the tub is removed and then rotated counter-clockwiseto prevent ki

7 Securing the product and re tting the tubDOUBLE MODELSA124543CCBBA56optionalThe mounting tabs are in pairs, one on each side of the product. At le